Hello, I am Major Alencar, I am the chief instructor of the fire support simulation section of the South Training Center, Army General Center, Geraldo Antônio Mioto. Today we will be presenting a presentation for the 7th Extension Course in Armored Combat Simulation Initiation. It is an honor and a satisfaction to be able to participate as a lecturer in this course.
In this presentation, we will talk a little about the fire support simulator. Our goal is to present the simulator and also report on its use in the training of the troops. We will follow the summary that is presented on the slides.
We will have a small introduction, then our development. We will talk about the function of fire combat, the fire support system, the concept of the system, the structure of the fire support simulator, the exercises that are performed with it and what is the methodology used in these exercises. Finally, we will have a conclusion.
The simulator emerged as a solution for the armies of the entire world, as well as the Brazilian army, to maintain the effectiveness of the training of the troops that provide fire support with the reduction of costs. The exercises that are carried out to train the troops that provide fire support require a high cost. In order to maintain this training and also enable the adequate use of financial resources, the solution was obtained to use the technology in favor of the ground forces.
With this, the simulators emerged as a solution, as I said, bringing the troops to a simulated environment, however, very close to the reality that they will face either in real exercises or in combat. Moving on to our development, we will now talk a little about the fire combat function. What is a combat function?
The combat function aims to train the army units to face the various challenges they will face in the fulfillment of their missions. It is an effective way to achieve the objectives imposed on each type of fraction, and they can also be divided into command and control, movement and maneuver, protection, intelligence, fire and logistics. The fire is nothing more than the application of artifacts, whether with kinetic or non-kinetic actuators, on designated targets, with the aim of bringing some kind of impact.
They can be low in personnel or material, in order to de-structure the enemy forces. The fire combat function aims to correctly apply kinetic and non-kinetic actuators to the achievement of the objective, with the main capabilities being the acquisition, discrimination and engagement of targets. The fire support system, which is a component of the fire combat function, is the set that encompasses the means, the staff, and the processes that will allow the appropriate fire support to the maneuvering elements.
This fire support system, acting together, will allow the elements of the ground forces to move forward, thanks to the fire support, hitting specific targets in combat. In the ground forces, this fire support is mainly provided by the field artillery groups and heavy mortar pilots, which make up the infantry battalions and the cavalry regiments of the Brazilian Army. With the use of fire, they can achieve a high power of destruction, capable of providing this support that I had mentioned, to the elements that are in front of the combat, mainly the infantry and cavalry troops.
In this slide, the intention is to show you how the fire support provided by a group of artillery to a brigade occurs. The artillery groups, according to the particular characteristics of each brigade, may have a variable number of 3 to 4 obus batteries that will provide fire support to the entire brigade. In these batteries, we have a number of 3 to 4 advanced observers who will be accompanying the maneuver along with the subunits of the infantry battalions and the cavalry regiments.
So, each advanced observer will be accompanying one of these subunits, adding up to a number of 10 to 17 observers, according to the brigade that will be receiving the support of this artillery group. We will now talk a little more about the artillery materials used by the Brazilian Army. Initially, we have the M109 self-propelled gun, which is a 155mm caliber self-propelled gun.
We have the L118 Light Gun, which is a 105mm caliber self-propelled gun, and is used by military vehicles. The M114 self-propelled gun is a 155mm caliber self-propelled gun, and is also used by military vehicles. The M101 self-propelled gun is a 105mm caliber self-propelled gun, used by the Brazilian Army, and is also used by military vehicles.
The M56 self-propelled gun is also a self-propelled gun, used by military vehicles, but it is a lighter gun. The M56 self-propelled gun is used in different environments, such as the jungle, the mountains, where lighter materials are needed to be transported. In addition, it has the ability to be disassembled and reassembled, so it ensures greater flexibility in field artillery.
Finally, we have the 120mm mortar, which is used by some Brazilian Army field artillery groups, and mainly by heavy mortar platoons, cavalry regiments, and infantry battalions. It is also self-propelled, and is also used by vehicles, and has a 120mm caliber, which is larger than some of our guns. Here we will talk a little about the use of the artillery subsystems.
In search of bringing the simulation of what happens in reality to the simulation exercise environment, we have the configuration at the bottom, as you can see. From the right to the left, we have the target to be shot, the advanced observers, the line of fire, and more to the left, symbolizing the rear of the friendly troops, the firing point. And just as it happens in reality, at the top you can see that it is a replica of the structure of the fire support simulation session, and we have rooms where each of these subsystems will be configured.
We will have the room where the observation posts will be located, where the advanced observers will be located, the room where the firing point will be located, which will perform the necessary calculations to reach the target. So, the observers make the elevation of the target, pass this data to the firing point, which performs the calculations, transforms this location into data, into elements of fire, so that the line of fire executes the shot on the targets. And the line of fire also has a place in the simulator, in the simulation session, so that it is unfolded as if it were also in the real environment, in the terrain.
In addition, we also have some other rooms in the simulation session that are components of this system in order to maintain the simulator and the exercise occurring as a real shot would occur in reality. The fire support simulator aims to support the training of the campaign artillery groups and the heavy mortar platoons, 120 mm, with a specific focus on the combat focus function. So, all the process that is done to execute a shooting mission, so that the fire support is provided to the maneuvering elements, all the activities that are carried out by the campaign artillery group and by the mortar platoon, in a real shooting mission or in a real exercise, will also be executed in the simulator.
In addition, the simulator allows the execution of fire planning and coordination exercises, more focused on the use of division artillery and the command of the army artillery. Our simulator has the characteristic of being technical and procedural, so it will focus on the techniques and procedures that must be carried out in each of these subsystems that I discussed earlier, employing both virtual and live simulation. So, we have the virtual representation of a real scenario with the simulation, and the troop will be performing the procedures as they are executed in reality.
So, it's a mixture of virtual and live simulation, focused on real shooting, be it artillery or heavy mortar. The structure of the fire support simulator. Initially, we have the servers.
This server room is composed of 31 computers. It is a complex that involves a logical network and a communication network. It will generate the computer data and transmit it to the other simulation rooms for video playback, via network cables, which will take this information and transform it into video and data that will be received on the computers of the other rooms.
In addition, it is a room that has electrical network stabilization by means of no-brakes, preventing any oscillation from affecting the image generation and the execution of the exercise. And it also has a carbon dioxide fire system that avoids any occurrence of sparks or a principle of fire affecting and destroying the structures. In addition, we have an administrator, who is responsible for managing the initialization of the servers and monitoring the transmission of data and the logical network, so that the simulation can occur in a correct and adequate way.
And we also have our auditorium, which is one of the rooms that will be receiving this data projection via video and, in addition, the transmission of communication, which is also possible between the rooms. In this photo, we have the way the network was assembled, so the cables were all passed under the floor of the room, facilitating access to any maintenance needs that we will have during the exercises or in the interval of these, allowing quick maintenance and correction of any problem related to the logical and electrical network of the simulation session. The observation posts.
We have a total of three observation posts, as you can see in the image. The observation posts have a curved screen with 9 meters in length and 3 meters in height. Their basic structure is very similar, only the layout differentiates each post, but the components are the same.
We will talk a little bit more about each component of the observation post, and the screen allows a wide view of the terrain by the advanced observer, simulating what he would actually face, the field of vision that he has when occupying a command post on the terrain. In the observation posts, we have a binocular, which is the employment material of the advanced observer, a goniometric platform, so that the binocular, when coupled to this platform, acquires functions of a goniometer compass, passing horizontal and vertical angles necessary for the data to be lifted by the advanced observer. We also have a compass, with a model similar to that used by the advanced observer in reality, which can also be used to lift the data from the target.
We also have a joystick, which is basically used by the instructor, the observer and the training controller, who is accompanying the troop. It has some functions of laser telemetry, advanced observer positioning, binocular reticle, employing night vision glasses, allowing the advanced observer to occupy the correct position, among others. In addition, we also have a simulated GPS that can be used by the troops, as well as the advanced observer will also have his GPS on the ground.
In the advanced observer post, as you can see on the slide, we have the projector that will receive the data through the network and transform it into the image that will be projected on the curved screen. We also have the radios, which are actually computers that perform the function of the radio, but they act as a radio that is used by the ground force for the transmission of shooting messages. We have computers that receive information and also pass the information to the exercise control center.
In these computers we have forms and files that the advanced observer would manually fill out in real use. They will be on the computer and he can insert them into the computer itself. With these forms filled out, the instructor who will be in the exercise control center, which is a structure that will be addressed later, performs the monitoring of the data that is being raised by the advanced observer.
The network also transmits the data to each periphery that was mentioned, the GPS, the agonometric platform, the compass, the binoculars. Here we have some more images of the observation post. The binoculars have the characteristic of having a 360 degree view, so not only when it is pointed towards the curved screen, it presents the simulated terrain.
In the other directions it will also be projecting the image of the terrain that is represented in the simulation scenario. Now let's move on to the shooting center. The shooting center of the group also has a logic network and communications interconnected to this room, allowing communication with the other rooms, with the exercise control center as well, and computers that have files and forms relevant to this subsystem.
So, remembering that this subsystem receives the observer's data, it has to transform this data into shooting elements. Precisely these files will contain the shooting elements and the data they receive, and which must be passed to the firing line that will fire the shot. These data are filled out in these forms and files, which will also be accompanied by the exercise control, the instructor who will be occupying one of the existing posts.
Here we have the representation of the shooting center room. The shooting center team occupies the posts, we have the computers where the files are stored, the radios, if you look at the computers, there is a green box, which is the radio, where the messages are transmitted, and the other materials that the team brings in order to calculate the shooting element. We also have the battery shooting centers, very similar to the group shooting center, they also have radio communication and computers with forms and files to be filled out.
Therefore, they also have logical networks that will be passing this data and communications with the exercise control and with the other subsystems and other rooms as well. The firing line also has a place here in our complex for training. The firing line, which is the place where the pieces are located, also has logical networks and communications for data transmission and shooting messages to be carried out.
Files that are accompanied by the exercise control are also filled out. It is noteworthy that in the firing line we have the computers of the pieces, and these pieces, the obusers, are sensorized, so kits of sensors are installed in each piece that will be transmitting in real time the shooting elements that will be inserted in each obuser for the control system in the exercise control center to carry out the tracking, if that procedure, if that element is inserted correctly. So, to capture this data by the sensors, we have a set of Wi-Fi antennas that will be able to transmit this data.
In addition to the elevation drift sensors, the drift is the horizontal angle direction that is inserted in the piece, we also have the loading and shooting sensors. So, there are sensors in the firing line that have the ability to check that the piece has been loaded, the ammunition has been inserted into the piece, and also when the shot is fired, it also recognizes that the shot, the process is carried out as it is carried out in reality, it recognizes by these sensors and transmits directly to the center of the simulator that it executes the shot automatically. As you can see, we have the kits of sensors installed in one of the obusers, there are several cables and we have the elevation sensors, the direction sensors, the loading sensors and the shooting sensors too, among others.
So, we have the computer that is placed in the piece where the data can also be tracked. And here we have the ammunition. If you look at the ammunition above and on the left, it is a 120 mm mortar ammunition, and these colored discs below are the ammunition loads, which also have sensors and are recognized.
So, depending on the load that is inserted there, the system recognizes each disc and automatically generates in the simulation system the load that is in that piece, that was inserted in that piece. So, if the fraction that is being trained incorrectly inserts a disc more or less, the simulator already recognizes and will execute as it puts the load in reality. It does not make the automatic correction.
It recognizes and executes the shot according to the load that is inserted in reality. So, if there is this error, the error will be replicated in the simulation. Below this figure we have another image, the photo that represents the ammunition sensor, the loading sensor, which is found in the ammunition cartridges.
And on the right we have the ammunition with its spool, which is another capacity that the simulator provides, that we have several types of spool, such as the time spool, which is registered a time that will trigger the spool and automatically the explosive load of the rest of the grenade. So, in certain shooting missions this time must be inserted, and the time to be inserted by the fraction must be the correct one so that it obtains the desired effect on the target. The Fire Support Coordination Center is another structure that we have available in the simulation.
So, this Fire Support Coordination Center is where the call officers will be working. They will be linked to brigades and battalions and regiments. They will be coordinating the fire support in the scope of these brigades, in the scope of these battalions.
And we also have in this environment computers with forms to be filled. They will also be accompanied by the instruction team, by the receivers and controllers of the training. We have a logical network, a communication network to allow communications with the other rooms.
We also have a computer that will have the representation of the terrain where the exercise is being performed. So, the simulated terrain will also be available to the call officers and to the Fire Support Coordination Center. So, we have the cartographic representation.
This cartographic representation is already in the 3D scenario, which will also be available in this room. And it allows the exercise to be accompanied and the necessary fire support coordinations to be made according to this terrain. We also have a room for the greater staff of the Campaign Artillery Group or Brigade.
Where the personnel, logistics, intelligence and operations of these groups will be acting. We also have a visualization of the terrain where the exercise is taking place. With a scenario that is generated, having a communication network and a data transmission network.
With the computers, each documentation related to one of these areas will also be filled. Logistics, personnel, intelligence and operations. We also have a room available for the division artillery.
In the exercises that the division artillery elements are used. It is the Tactical Operations Center, the COTE of the AD. Also where computers with documentation to be filled and data transmission are available.
Communication network to allow the connection with the other rooms, with the other structures. And you can also see that in this environment, this cell has search elements for targets. The coordination of this search for targets of interest.
It has unmanned aerial vehicles, VANTs. In addition to that, the radars. They are represented in the image and will also be available for the use of the division artillery.
Now let's move on to the Exercise Control Center. The Exercise Control Center is responsible for managing the simulation. Manage the course of the simulation exercise.
So we have four instructors in this room. Where we have computers. Each post has a series of computers with screens that have specific functionalities for the instructor who is sitting there.
It also has a network of logic for data transmission and a network of communications. In addition, we have an auditorium where the scenario is projected with the effects of the targets that are being hit. And the execution of the exercise.
In addition, the instructor who is there in the Control Center has the ability to monitor the transmission of the communication messages. The shooting messages of the artillery group or the heavy mortar platoon. The instructor can monitor the files that are filled, the data that are inserted in each form and file and also the data transmission.
By ear. As an example, we have one of the screens that is viewed by the instructor who is there in the Exercise Control Center. This is the main screen where he has several menus where he will manage the exercise.
So he is monitoring the shooting mission, the data that is transmitted, the elevation, the drift that is generated in the simulation. And he just inserts at that moment the drifts and elevations that are calculated by the troop. He can also monitor the meteorological factors.
Wind, wind direction, rain insertion. There is this possibility. In this part he can manage and insert the data.
Where he will position the targets, where he will position the fire line, where he will position the advanced observer. It is through this menu that is displayed up there. This is another screen.
Here we are monitoring the weather conditions, atmospheric conditions. So it is possible to change them as I said and also monitor them. And according to each exercise, a meteorological message is also generated.
Meteorological bulletin. Just so that the troop takes knowledge and makes its theoretical preparation, given the interference that each item of this meteorological bulletin can interfere in the accuracy of the shot. Wind direction, for example, is one of these.
According to the values, it will take the necessary calculations to achieve the necessary precision and achieve the effects on the target. So we have here a little of the representation. Above the left we have the operator of the exercise control center.
The right is above our fire line. And below we have the advanced observer post, below to the right. And below to the left is our auditorium, where the 3D scenario of the terrain where the exercise is taking place is also represented.
Smart's components and peripherals. So we will now see some components and peripherals of the fire support simulator. On the left we have the no-brake, which is composed of 30 100A batteries.
As I said before, its purpose is to keep the electrical grid stable and protected from oscillations that occur in the grid. Preventing any type of damage to the electrical structure of the simulator. In addition, we have projectors in each observation post, as well as in the auditorium.
Projectors to the molds of what is in the figure on the right. These are projectors used in some cinemas. So it has an advanced resolution capacity.
And they project the images acting together on the 9-meter curved screen, representing a wide field of view for the advanced observer. In addition, the SIMARQ has a number of other components. In addition to the sitting components, we have other peripheral components in the simulator that cover the entire simulation session.
So there are more than 1,000 meters of cables in the SIMARQ structures. We have two electrical grids, four logical grids, more than 100 computers operating together. Two sets of no-breaks.
More than 20 air conditioners that provide temperature stabilization so that the computers and the simulator structure work properly. There is no oscillation of temperature that affects the structure and harms maintenance and harms the exercises that are carried out. An intercommunicator system that allows communication between the different rooms.
High-power sound system. And the Wi-Fi antennas capable of capturing the data from the pieces and transmitting it to the high-precision simulation system. Now let's move on to our exercises.
The exercises carried out in the SIMARQ are campaign artillery group exercises, heavy mortar platoon. It is also possible to perform artillery observer exercises or any weapon observer. And fire coordination and planning exercises, which are carried out in the divisional artillery of the Army.
The execution of the exercises is based on a tripod, which involves technology, training and experience. The technology will add the capacity of simulation to bring reality to the troop in the SIMARQ structure. The need for training is precisely to consider and adapt the level of the faction that is performing the exercise in the SIMARQ and seek to give conditions for it to raise this level.
And the experience is based on the experience of that troop that is being trained and the instructors who, using this capacity, will elevate and conduct the exercise in a way that the troop takes maximum advantage in order to expand their capabilities and reach a higher level of training. In the conduct of the exercises, we have four members of this process. The microcosm, which is precisely the tactical context in which the faction is inserted.
It performs an exercise being integrated into a tactical context, inserted in a certain tactical situation. The stressors, which are the simulated military problems that are placed on the troop for it to solve. Basically, in the artillery and mortar platoon, it is the targets and firing missions that it must perform to cause effects on the targets.
The entries and exits, which are the stimuli and the responses that are extracted and imposed on the faction so that it has the appropriate solution. And the processes and tasks, which are the procedures that should be known both by the instructors and by the faction so that there is a reduction in failures and errors during the exercise, generating progress in the level of training. Here you can see that the CIMAC of the South Training Center, it acts supporting several units of the Brazilian Army.
They are the Campaign Artillery Group of Rio Grande do Sul, Santa Catarina, Paraná, which involve the Military Command of the South and part of the Military Command of the West, more specifically of the State of Mato Grosso do Sul. We now move on to the methodology of the exercises, the mortar platoon and the artillery group exercise. As a first event, we have a shooting mission in which the time of the execution of the shooting mission and the procedures that are carried out in it is referred to as initial verification, in order to understand the level of training of the faction that is arriving at the fire support simulator.
After it, we carry out a training phase by subsystems, which will be detailed a little later, and then we move on to a joint training, which is a third phase. And permeating all these phases, analysis and post-actions are carried out, which are debriefings of how the situation is, of opportunity for improvement and strong points of the troops in each shooting mission. At the end of the exercise, an initial verification is carried out, which is a shooting mission similar to the one carried out in the initial verification, in which we find out what is the level of training of the faction at the end of the training exercise in the CIMAP.
And at the end of this verification, we carry out a final post-action analysis, in which all aspects that permeated the training exercise are addressed. In order to explain to you the training exercise in the subsystems phase, I present this slide that you can see. Each subsystem is directly connected to a training control observer, which will be occupying a position in the exercise control center.
On the left, we have the observation post, as you can see. This observer will be in direct contact with the instructor in the exercise control center. There is also a shooting center.
So, the instructor who is occupying the instructor's position in the exercise control center, will sometimes be doing the other subsystems. On the firing line, the OCA will be in direct contact with the faction that makes up the firing line subsystem of the exercise troop. The goal of this phase is precisely to gain greater flexibility and dynamism in the execution of shooting missions, to level the training and internal knowledge of each subsystem, and to raise the level fractions from the beginning.
Each subsystem must raise their level together. You can see that we still have other posts that can be interconnected with other subsystems. So, we can connect a second PO with another instructor's post.
We can connect another shooting center to an exercise control instructor's post. We can also insert another sub-unit of a second sub-unit with an exercise controller, with a training control observer, following this fraction. And in the joint training, the observer is in direct contact with the firing center of his faction, which will also be in direct contact with the firing line of this faction.
And the instructor who is in the control center manages this interconnection. He monitors the transmission of data and phony messages from the firing missions. So, we still have the ability to manage two training systems, two fractions acting together in this training phase.
Our GAC training, you have an idea. So, it happens every week, it starts with an adaptation environment, as I said, the initial verification. The training phase for subsystems is still in the same day.
And from the second day, on Tuesday, the joint training begins. Where we started on the first day, carrying out firing missions in order to solve the PMSs, which consist of the objectives of the basic training programs at the sub-unit level. And on Wednesday and Thursday, we move on to the constant objectives for the unit level.
On Friday, we finish with the final verification and the post-action analysis. In the heavy mortar platoon, since the number of fractions of this type is much greater in the desert area, and seeking to meet a greater number, we carry out two exercises within the same week. So, we start with an environment and adaptation.
We move on to the sub-systems training phase. On the next day, we start the joint training phase and finish with the final verification and the APA of this first platoon. On the next day, on Wednesday, it is the return of this first platoon in its firing mission.
And we start the environment and adaptation of the next platoon. Moving on to the sub-systems training. On the next day, joint training.
At the end of this second day, of this second platoon. Final verification and its respective APA, so that on Friday, it can return to its firing mission. So, in order to exemplify the costs involved in a campaign artillery group exercise, we have the exercise of the 13th GAC, carried out last year.
It consumes ammunition of the type 155mm, whose value is around R$ 9,200 last year. This value has changed for this year. So, we have more than R$ 23 million, which would be expenses, estimating only the consumption of ammunition, to carry out an exercise of the same magnitude in a real way.
Well, concluding our presentation, I bring here for you a little bit of how this retrospective has been, estimating the costs involved in the exercises here at the CIMAF, from 2016 to last year. So, if you look below, you will see that from 2016 to 2023, there is an estimate of costs that would be used to carry out an exercise of the same magnitude, of considerable value. I will not address all the values here, but you can see that they are significant amounts.
Below we have the updated values of the ammunition, so there is a significant difference in the values for this year. Each exercise involves a lot, considering the financial resources to be delivered in high-value ammunition. So, the importance of the simulator in the use of training is considerable.
And you can also see the number of shots fired in total in these 7 years of existence of the CIMAF, more than 240,000 shots, millions of reais that would be spent to be able to carry out an exercise of this magnitude, and also to be able to maintain an adequate level of training of the Brazilian Army fire support units. I close my presentation. I hope I was able to meet your expectations.
I wish you all a good course.