[Music] guys a quick introduction with with Alin myself uh I work at Rand on our structural side of our business so I do a lot of simulation with an an mechanical package as well as with altina so one for more implicit one for the the explicit applications um so today uh I want to give an introduction for the dino package right uh the primary agenda really is I have three Things I will go over with you one is a quick overview of the D capability uh just show you what it can do in general um
second is I will go over a quick uh General workflow using an example a very simple example problem sort of you know letting you guys especially if you haven't touched the software before to get a sense of what you have to do to be able to say for example trial the tool to see if you can use it to help your business or help with your personal Development right what does it take to set up a model what are the things you need to consider and the third thing is I I'm going to talk about
some very general simple applications right the the third part really is to let you see just the amount of potential application that the dino package can be used to to to simulate basically it's a physics based tool that can be used in in a much wider range of applications than a single code that you have in in in other Packages which is really in my opinion one of the most defining characteristic for for this uh uh Faba code right and it's also why it's honestly one of my favorite I I personally really love it because
of its truly wide range of capabilities okay um my target audience really like it will be really good if you guys have done some FEA in the past right but even if you haven't like this is not a a really technical presentation it's truly an introduction but I'm not Going to go into a lot of really simple detail uh detailed explanation for specific terms um I'm assuming that that you have some understanding of that but it's even if you don't it's okay it's not a it's not a big deal okay all right let's get started
so uh Dina right really is known for explicit Dynamics right so when you hear the term here really just means highly transient highly deformable highly nonlinear uh physical phenomena Right so for example this is a very well-known recently published uh Lego crash animation right on the left hand side it's a actual physical test with these Lego build cards on the right hand side is a simulation environment right so you can sort of see the amount of detail the package is able to to pick up uh and Dina is very well known as H say one
of the only two that's used for crash right so if you want to do crash simulation like you just want a crash Carard in your career there are certainly folks out there doing that this is really one of the only two out there that people are using uh is certainly the market leader right 17 out of 20 top auto companies are using this and in terms of speed which you know as far as a program goes right it's one of the defining things that makes it better or worse is how quick can it go and
it's it's highly uh uh it's extremely fast in terms of its Par parallel processing capability which means as you invest in Hardware the the model runs faster and faster it scales much better with Hardware investment okay so once you look at uh a very in terms of crash right so I could take a truck model uh from the Open Source on uh resources online and then crash it against a post right just for the sake of demonstrations right we can also take two cards you know aligning some orientation and crash them against each Other and
you can sort of sort of see these detailed defamation around the bumper all the stuff inside underneath your hood right and a lot of people are doing this type of work right for for their their employer for their organizations uh in terms of applications that I obviously go into right this is a very specialized world and it's very much what Dina is is known for right but you know my my uh and then one of the things before I go into that One of the things is that if you are a purchase of alasta you
are you are going to have access to these uh Baseline model these are the vehicle models this the tire model this is a human body model this is what's called a barrier model right so you can actually get access to these Baseline models uh and basically say for example if you are the one of the guys that are designing a barrier right you can take one of vehicle model and just run against your Own barriers so these are the things that people have created in the in the in the dino Community to allow you access
to these uh which helps you with your with your organization if you're go is to do say crash and occupant safety and so on so forth right but as I was saying you know Diner really is about much more than just explicit Dynamics I think in a lot of ways you know if you look at the true range of capability inside Dina it's also extremely powerful In implic side right so for example if you want to do analysis that's highly nonlinear right which means you're going to see a lot of deformations but also in which
the duration of the physical event is extremely long right in those cases right if you're familiar with with the the the the simulation world right that's not really suited for explicit because the duration of the physical event is so long even though you have a highly nonlinear event right in a lot of Those cases right dinina is also extremely well suited for those type of problems you can also do thermal problems to electr itics problems you can do mvh like nor Modo analysis do response Spectrum you can do things like forming right you can also
do say for example some cfd problems right um and there are also things within the particle uh within the element free method which I'm actually going to demonstrate today right that allows you To handle problems in which the defamation is extremely large uh in which a lunian method is no longer the the the most suited for it right so in terms of the capability within the code that that that you'll be getting right is is so much more than what it's mostly known for right that's the first thing to know and the second thing to
know really is that it's not just a structural solver right and I sort of I sort of hinted at that earlier right It's also a multiphysics solver right so so what that means is that you know you can do a fluid and structural interaction which is which is a simulation that involve both structural analysis as well as well as cfd analysis right and then you can also do a combination of any of the other multiphysics problem that you can sort of Imagine right so if you've ever done uh FSI problems like fluid structure interaction problems
right usually it Requires the the program to talk to each other in between uh uh steps right in between your simulation steps and that you have to check for convergence for that data transfer and that's the type of thing that no longer truly necessary within a a within Alina because you you are solving the problem within a single code as opposed to having to use two different programs to do it right so so these are things that are very very unique to Dina uh but Obviously it's sort of for for more advanced users but knowing
that capacity right really help us appreciate just what what the program can do right okay so here's some very quick example right uh of this is a tank fuel tank slushing uh which has a impactor coming from the right hand set once it impacts it you can sort of see how the fuel start to behave inside the tank so it's like a typical slushing problem this is a the Orion uh uh uh crew module hitting Against the the the floor which is made of water right this is a p pouch which has a sort of
fluid filling filling into it uh this is a ballistic problem which is penetrating a ballistic gel right so these are the type of thing that in my mind is much more multi physics right even though not all of these are done with a multif physics solver right some of this done are done with the with element free method uh which we talk a little bit today hopefully right but Knowing this capability right these are things that that is really you know sort of explains the type of things that you can expect to do inside Dina
which which uh uh usually requires you know uh you know more than just a structural package sometimes right okay so let's look at the basic workflow all right uh you know din like any other package right really you have three components you have the pre-processing you have your post-processing and then You have your solware itself right so when you buy the software right and this is one of the confusing things that I've often heard right is when you buy the AL product what you're buying is not a pre-processor or a postprocessor what you're buying is
the sofware itself which means it require to require an input deck to generate a bunch of data a bunch of files which is going to be read by another program right so a pre-processor is what's going to create An input deck and input deck is fed into the software which is what you're buying and then when the s when the the the program finish executing is going to generate a bunch of files which is readed by a post processor right and that's the the essence of of a workflow per se right so when you're buying
this remember you're first of all buying the buying the software then you have to decide what is the pre-processor you're going to be using and what is the Postprocessor that you're going to be using right so industry has currently a few pretty standard uh pre-processor and postprocessor they're using right so hypermesh and VAP are two packages that are not an an product right these are product outside answers that a lot of people are using out there right you use hyper match to pre-process and you use hyperview to to postprocess and feac has has both uh
the the pre-processing and post-processing capabilities now Alis Prepost is a free software that anybody can download right even if you don't own the product you can download LS prepost uh which allows you to basically build a model right and it also allows you to read the data that's generated by the solver after you feed it and input that right but obviously without the software it doesn't really do anything because you can't you can't solve anything even that's why it's free but other press post being a free processor and Postprocessing uh tool right is essentially what's
created by lstc and this is the the the tool that's uh sort of like you know if you don't want to use any of the other ones you can use this one of the downsides with all prep post is that it's it's mildly difficult to use right so it certainly has a much steeper learning curve like I myself do not use it for post for pre-processing I use it for for post-processing uh because for pre-processing I think there Are just better ways to do it that's much less convoluted and it's also uh has a stronger
association with your cat interface right which makes it you know less ideal for myself right so the the me you know Ransom being an Anis house what we use is What's called the workbench Alis D so when anes purchase the creator of of Alina which is LC right so they started creating this pre and postprocessor called a workbench Alisa which is thing that you can insert Into your workbench so hopefully most of you guys have used the the tool in in ansers right so you can drag and drop something like this into your workbench right
and that's essentially What's called the workbench Al dyam right it has your geometry prep to and your model uh similar to any an mechanical model um and this is a tool that's very much similar to a typical uh aners pre-processor right but it its goal is to create uh uh the input deck which is Going to be read by the solver and it's it also has capability to postprocess information that's that's that's being uh written by the solver right so this is in my opinion going to be the future and then for no other reason
than the fact that because answers is creating this right so because LCC is not aners product this is going to be a a a dominant pre-processor in the future uh because aners is going to make it better and better and better and suited for our Customers so keep in mind right so I'm going to do a demo today using this uh in in in a little bit right and you guys can sort of see what what that will look like okay and in my opinion this is a very easy to use Tool uh certainly with
things that you have to get used to but but it's going to become better and better in the future okay so what does what what is the essence of of the dino workflow right and I I think you know you can you can go through a a de Demonstration of the tool and so on so forth but really the only thing that you have to take away is that any object which means like in this case I have a contact object that's created inside workbench Diner right I have an edge contacting a I have a
bonded contact between an edge and a surface between two tubes right two square tubes and then I'm going to bond them together right that's an object that you're creating in your model right Anybody can do that pretty easy to do um but what is actually happening right is when you're creating an object like this inside dyo what's actually happening is a key card that's generated look like this this thing is what's going to be recognized by your input deck by your by your solver right by the by the dyo solver uh all of these little
things that you're seeing here uh in this presentation we won't go through them what they mean that all that stuff right But basically these are the individual parameters that defines what the contact is supposed to do right so if you think about a bonded contact what what are the parameter of a bonded contact these are the things that you are you are going to have to indicate in your GUI right in your graphic user interface which is going to allows you to Define what the car look like which is going to tell the tell the
solver what to do with that specific contact object okay that's the Essence of it right so so really when you're building a Dynam model you're essentially constructing a set of cards that's going to be recognized by the program to generate a set of response information for you to to read in your postprocessing uh tool right so you know when you look at a contact card like this right I I chose a contact card because it's actually the more complicated one right a contact card will have the name of it right here Right you will have
what's called a mandatory cards which means every single contact card doesn't matter if it's a bonder contact or frictional contact going to have a set of command parameters that you have to input these are the mandatory cards you also have what's called optional cards these optional cards is going to Define things like contact methods it's going to Define amount of penetration allowed uh uh and so on so forth right there's a Lot of different things right each of these little parameter right here you can actually go read about them to see what they're trying to
do obviously I won't talk about them right right but here what we have is what's called a tied noes to surface so if you can read this text right here right this underscore is what tells the computer what is what what he Tred to look for right so tied means it's bonded nodes to surface means we're are tying a bunch of Nodes to a segment which is called a surface okay and that's the clue you can sort of get what what is Dina trying to do with with these cards now remember all you have to
do is to to input things into a guey right it's going to pump a card out and and then you're going to have to make sure the card is right by changing the guy to make sure you get the right card and that's the entire process for for for correctly building Al model is you need to understand how Is your pre-processor interacting uh uh uh is behaving to generate the carsa and what kind of behavior is being indicated by the model that you're setting up right and that's the the really the nature of the process
of learning how how to correctly set up an Al model right and of course you need to do it for every single object in your model uh could be a little in the beginning could be a little difficult but once you learn it it becomes easier And easier to do right and this is the basic scheme for a contact card right so you can sort of see uh there's an option one which is the first keyword is going tell you what is the type and then the fourth keyword is going to tell you the offset
options right so all we have we didn't have option two we didn't have option three because we ski them because it's not a thermal uh pair right we're also going to need ID so so that gives you an ID and then for every single car You're going to have some kind of uh syntax just like a pro programming language in a way that you need to sort of understand uh you know you learn it slowly right but once you learn it once you realize it gets easier and easier and easier to understand okay now so
so why is this a a good thing right so some people might say I really don't like to look at these these code and as I mentioned I think you know in the beginning it might look like something Like a hurdle you want to overcome but once you overcome it once it gets easier and easier and easier to understand and the second reason it's a good process is because you know if you ever think about why how do you how do you know the model you're setting up is correct right you want to look at
the components of that model right if the components of the model is all individually set up correctly you know you have a good model right but how do you know that Individual component is set up correctly you look at the key cards if you know the key cards is being being created in a way that that that corresponds to the design intent right for example if I have a bondet contact do I need to Define at what point does the bond contact break uh uh that type of thing right if I wanted to define something
like that I can do that and that kind of behavior is what's defined in the key card right so when you want to generate A good model you have to make sure the individual components are captured and within the component we want to make sure the key card corresponds to how we want that component to behave like for example material for example contact for example a boundary conditions right any of these things can be individually looked into to make sure you are generating the correct uh uh uh input deck right a correct key card and
that's the nature of a first principle Decomposition of a difficult model into components that you can you can investigate and study and that in my opinion is why this system actually works really well once you really get it used to it right okay so let's quick let's look at a quick example right I'm not gonna gonna gonna uh uh talk too much about cards right but what I wanted to do with this example is to show you how I will set it up inside workbench Dina uh without having I'm not going to Do a demo
here because we're limited on time right but I'm going to show you what the model look like and I'm going to talk talk to you a little bit about how I think about setting up something pretty simple right so this model is essentially like a a rubber ball right so this ball right here is a shell body I I know I'm not really showing that uh he going to have have have some kind of like you know air pressure inside it which I'm going to Define I'm going to Drop this about two meter from from
the ground right which which is right here this is the ground and I'm have a drop height defined which is going to translate to some kind of impact velocity so as you can imagine if it's a rubber ball hitting the ground it's going to compress into a smaller volume then bounce back right that's a pretty pretty simple example it's also an example involve an airbag model it's also an example That's the basis of any Drop study they will do right but it's a very very simple example but if I show you quickly what the workbench
dyam model look like this is pretty much it right so I have some component uh being imported I have a corner System created right I have a bunch of a name selection created so if you're familiar with this interface that that's essentially what I did right a couple name selections a cornate systems a bunch of uh body being imported from from CAD I have a couple Uh uh material model being written into the into the input deck into the pre-processor and then I have a fi airbag model right and then I have a gravity uh
inserted and then I have uh a rigid wall which is acting like a ground and that's that's in essence what what what I did and then in the presentation site I'm going to show you guys sort of a step by step what I'm doing and what I would thinking about when I when I created it right because I think that's The nature of of that's really what's important right and even for something this simple okay so if we look at you know first step right I'm going to import the geometry so when I import the
geometry this is the shell body I'm going to define the shell thickness which is in this case is 15 millimeters right as you can see this is a 15 millimeter shell this is this all these body are being mesh with the shell element with a 15 mm thickness right so I have five different balls the reason I have five different balls is because I want to change the air pressure between them to show you what happens um so you can sort of think about in your head now what what's going to happen if the pressure
is higher versus lower think of basketball right which one is easier to dribble if you have a higher pressure basketball or lower one um now when I input when I import a geometry right what's what's happening in the input Deck site is I have a part card being generated I have a section card being generated the part card just tells you the program which what is the part number right and then you have a you have two things which call a section ID and a mat ID so so material and section section is right here
section defines like for example things like element formulation and shell thickness obviously I'm not going to go too much into it but knowing that these things These things are what's happening in the background as you as you just import geometry and measure okay now of course there are nodes and elements stuff that are that's not showing on the screen just know know that they exist they get written into like a text file right and then next is that I'm going to define the material of my ball right I want I want the ball to be
made of of some kind of rubber right so I have a dummy rubber material right a Mone riving material Model for for rubber I'm going to use it this is the basic information so even though I have a structural steel being being defined in my in my geometry I overwrite it with a text file with a keyword snippet in Dynam which is going to override the material with the Mooney rivin rubber right all I did here is uh I I'm tuning the program what kind of material model I want to use for my ball right
for my for my for my shell for my ball ball material ball body in this Case this is also what's happening in the input deck I basically inserted this card into my input deck right and then I'm going to insert a corate system uh basically tell me I want to I want to tell the program what's the orientation of my drop right uh in this case that's why I have that corent system so you see I have a global one I have a local one so I I now have a defined coordinate system card in
here I have a local coordinate system card in here right so What I mean what what I'm doing really is you know for every single object I insert into my pre-processor start thinking about what's the corresponding key card that's being created and how do I make sure it's done correctly right so so it's really not a a program in which you can follow a set of instructions every single time and you will do do it correctly every single time right it's not it's not there yet maybe I should say right but but it's also not
what you Want because you want to control the behavior of your model especially when the model gets complicated okay so so the mentality that we want to have as a simulation engineer doing dyo work right is to really get into the understanding is what are we doing in the in the pre-processor and how does it correspond to the input deck that's the mentality that you want to get into and which is what I'm demonstrating today okay and next I'm going to generate a bunch of Name selections each scoping to the body of the ball I
have five different balls you notice now I have a I have a selection ID here right so why did I do this the reason I did this is so that I can tell the the the pro how the later step of the of the model to use this ID to do something with it right so for example so what happens when I when I generate name selection inside Workman chal dinina I'm creating these set part cards which is going to scope that body Into a set now the idea of a set is that you can
call on it and then you you can then do something with it right that's the idea of of like a set right so now I have five different body with five different set ID and these are just essentially parts that are becoming part of a set right so why did I do that I'm going to create an airbag model for each of my five balls right so for example when I created an airbag model inside my inside workbench Alina I'm going to Scope to the name selection right and then correspondingly it's going to create an
a key card inside the input deck called airb Simple pressure volume now now this might not mean much to you right and I put in some information so as you receive this in the future if you want to look at what each of these parameter means you can look at it but basically the idea here is that I'm going to have to tell the program uh what's the amount of pressure I should Have inside my B it equal to zero right before it hits the ground what's the inflation pressure of that of that ball and
with a very simple airback model you don't have any leak right you don't have any temperature increase as the pre as the volume decreases right as the pressure increases uh things I this doesn't exist for a simple airback model all I'm going to do is I'm going to correlate the relationship between my pressure and my volume based on a single Parameter called CN this CN parameter right here is right is this number right here and then you know without getting too much into the math right this is a pretty simple algebraic math essentially as you
increase the value of your CN number right which is as you increase the value of of of what's in the tabulated data here right this this value right as you increase this value you are going to make the number uh make the pressure in the air back bigger as The volume decreases right which means it's a it's a it's a way to represent inflation pressure without directly indicating what that is right so it's a it's a relative term uh uh based on the size of the of of the ball and that's the essence of what
it is right so as I as I change the CN number from from right to left right you can sort of imagine the inflation pressure gets higher and higher and higher even though I didn't specifically calculate what it Is I can show that in post processing and mostly for for the purpose of this demonstration I'm just showing that as a in a sense of just increasing it what happens right that's the that's my goal okay so next thing we want to do in Step six right is that if you look at uh an object called
Dynamic relaxation which is what I what I created next right Dynamic relaxation is essentially a way of generating what's called a preload right so so why is that necessary here Is because before the ball impact the floor I'm going to have to tell the program to inflate the ball right and that that has effects that we have to understand so because you're intr introducing load into the system right in a dynamic analysis things start vibrating so we want to make sure before we start the analysis right we're minimizing the kinetic energy in the entire system
uh and then the nature of a dynamic relaxation right is Essentially a way to preload your entire model in an in an explicit sense right until your kinetic energy goes to to a very low amount so all that really means is that you're just pre-loading the structure until you have you don't have a lot of ringing in your system right your body isn't just ringing around before it starts analysis and that's really what it is it's it's a form of preload uh this is a remember this is an object I inserted into my pre-processor So
what is it actually doing what's most important what is the card uh that's being generated which I guess I actually didn't show what's the card that's actually generated in the in in in that but basically what it is is that it it's telling to preload until some threshold is is hit okay so in this step I do a preload uh once I do a preload right I'm going to have to define a floor which is what bar is going to hit right uh uh and that's essentially what this rigid wall Is this rigid wall basically
is a planer wall with some coordinates that you're going to find in space right and it look like this right so you see there's a floor right beneath my ball right and that it's going to contact every single body in the model and that's really what the rigid wall is you don't have to define a contact PA with a rigid wall it will just do the contact for you as part of the the the behavior of this card is that it creates a floor that you can Sort of see in your pre-processor and the the
the ball uh which while already being inflated in the preo step is going to hit the hit the floor and bounce back right and that's truly for the most part the the entire model right in a quick way I've explained both what I did and what I was thinking about right and then lastly I guess I got should talk about is the the control cards uh you know control cards are basically just Global level control that you want to implement Into your model so if you're familiar with the explicit Dynamics right so for example Mass
scaling is something that can increase the runtime of your explicit analysis uh in this case I just said it to know and that's a global control that you can set in your termination control termination essentially controls that you can also do Global contact control Global hourglass energy control and so on so forth right so we won't go into much of That but these control cards are are uh a a global level a way in a global level that you can control the behavior of your model right so for example for every single contact you want
to you want to contact behave in a specific way you can generate a contact control setting such that it does what it does okay um um you know we don't need to go into too much of detail this is something that once you dig into the program certainly you want to study upon Right um and then lastly how do you submit a job right so once the model is set up right there are three different ways you can submit a job uh the first way is what's called alas run so if you go to your
windows bar if you have the program go to your windows bar you search for alas run right Al run is going to ask you to to point it to the location of your input deck right which is the first line and then it's going to ask you to point to the location of the Solver which by the way is that single executable file that you spend a lot of money buying for right that that's essentially the solver which is your point into and you're going to Define how many core you're going to use you're going
Define the memory requirements which is usually calculated for you right and then that's that's going to allow you to submit the job right now the SEC what this thing requires that you have to write out the input deck Which in the case here is that you basically just go to go to here and then you just go to your aler so and then just do the do the environment and then write input deck right here right that's what what is going to allow you to to uh to write on the input deck and that's what
what the alrun program needs you can also do it directly inside work sign by just clicking solve right that's also works it does pretty much the same thing in the Background uh with some limitation I've ran into uh my personal preference is to use a third way which is using a a command line interface which is very similar to all run it really does exactly the same thing uh except I instead of requiring instead of using a program to write the script I just write it myself it's really not that different from all really exactly
the same I just I just I just write you see this expression right here I just write out That expression myself in inside a script which is going to allow me to submit my jobs or I would Define where to find the input de and where to find the solver and so on so forth okay and and so you can sort of see right the way to submit a job in Dina you know you basically just tell the the solver where is the input deck and that's it that allows you to to to submit a
job to to the to the solver and then you can and he's going to generate a bunch of files For you to read inside the same folder where your your input deck is located right that's your working directory okay um and then you know and then uh when you solve it you're going to see text file look like this right so you have a dynamic relaxation and you're going to give you a bunch of text file right and then if you look at the actual explicit model is going to give you the tal to one
in the cycle 250 cycle 5000 and this right here is your stable time Increment if you're familiar with that that's basically is how quickly your simulation is running and that's defined based on the size of your element based on the modulus and based on the the density of your of your uh of your material right so you can actually look at what that would be by inserting a CFL time step in your pre-processor right and this object right here lets you see what is the smallest time step in your model and That gets scaled down
by 0.9 by by this TSS Factor right U but Bas which is why this number right here 1.67 to negative say is a little bit smaller than this number um but you know idea behind it is that this is what you will see when you solve the model is that you're going to see a text file that look like that that you can essentially observe right remember for the most part it's explicit you can also write Place analysis which is going to give you a different text File uh that we're not going to talk about
in this uh in this webinar per se okay all right and then once all of that is done right you're going to have essentially a result file which obviously there's a lot of things you can probe but all I did here is that I don't know if you can see the the ball starts uh hits the floor compresses then bounce back and this is the air back pressure over time right so you start with some inflation pressure it's going To shoots up and it's going to come back down until equilibri Ates you see this little
wave right here is when it damps out the waving the the internal pressure until it reaches the equilibrium state right and then if I look at the next one I have five b with different inflation pressure the higher inflation pressure is going to bounce back a little bit more lower inflation pressure is going to bounce back a little bit less as as you would expect right um and that's Really the the the process for setting up a pretty simple model right is that you know it's always about what's in the pre-processor and what's in input
de and you know as you get more proficient with the tool as as an introduction right I couldn't I couldn't stress this enough is that you want to build a connection in your mind between what's in your pre-processor and what's in input deck right the the more you are proficient with that uh the better you are with the Tool and that's really what's required as an engineer I think to to get proficient with the tool is to start building that connections and then of course to read the read the the documentations um I think you
know for the engineers on the call right I I think a lot of you will appreciate the fact that you know learning is about reading and practice reading and practice and reading and practice um um and that's that's really our job is to To be technically proficient in what we do and to add value by by the you by the leveraging physics and leveraging numerical methods right and that's really what our job is so really no matter how complicated a model is right the key is to managing the purpose Behavior interaction and the nuances of
the keywords right so when you when we talk about doing a workflow for Dina right what's the takeaway again is how do you build that connection right Because any model becomes simple as soon as you can decompose you can you can start building this connection because for any challenge any difficulty you run into you can look up what's wrong and fix it right because you're building that connection you're not assuming how it behaves you can look up the documentations to figure out why it's not it's not behaving the way you intended for you to behave
and then you can fix it right okay so that's really a Quick demo right um and then know hopefully you're not you're not too bored at this point right you know hopefully you you get you get a sense of what what what you will have to do to get to get into the tool right but what I also wanted to to draw your attention to is some applications right because this is where really the fun begins is that you're not just looking at these boring key cards all day right that's not what the to is
right the two is once You master it the amount of application that you can you can manage right in explicit in implicit in thermal in electromagnetic in fluids in their multi interaction multif physics interactions right is so beyond what I think one person can manage in a Lifetime right it it's really cool in my mind to be able to to do so much with a single code right because I don't have to switch to different package when I want to do something else I can really Just stay here and do it and he had a
demonstrated success in a lot of different area right so I want to show you guys a couple really simple examples um I think I prepared five or six in the next 20 minutes I'm going to go over them so very very quick right and remember these are not like a a a a a patented uh product these are me using a c package drawing it up to show you what it is right literally I created these they're not they're not manufacturable Even in some sense okay just but treat them as an example as a demonstration
of modeling technique and and also a demonstration of what's possible okay so in the first example I have a fan this fan uh is essentially rotating like imagine there's a ceiling here right I'm I'm going to rotate this fan at four at 400 RPM right and now I have a soccer ball here now it's not really a soccer ball because I'm I'm lazy enough to use the same uh air uh some same rubber ball Model I used earlier right I'm just going to use that that that rubber ball and then I'm gonna impact that rubber
ball against the fan and then I'm going to ask the question what do you think is the stress on the fan as this rubber B hits the fan while the ball is traveling at a th000 inch per second and the fan is roting at 5 400 RPM per second like what's going to happen to the fan uh when when I do that right um I don't I have no idea but that's like seem like a Very interesting question to ask with the tool right so um basic setup I'm going to go over it real quick
or really don't want to get into like how to exactly do it right but basically I have a bunch of contact which is going to bond the the different body of the fan together right because these fan have individual blades which are slightly angled and they have different connection with the center piece that I created I'm just going to Bond them together for the most part and remember these translate to some contact cards I have a frictional body here which is between the the surface of the ball and the bottom surface of the fan blade
right because I want that to be a sliding interface therefore it's a frictional contact pretty simple right um I'm going to have some initial conditions right which means I'm going to start the analysis with the fan rotating at 400 RPM and then I'm going To start an analysis with the ball traveling at a th000 inch per second in this orientation here with this accordin system that I created here right pretty simple to understand now remember when you have a when you have an initial condition you have to do what's called a dynamic relaxation again right
that's what I introduced earlier uh if you remember and that's basically my preload so I preload my structure before I do the actual impact analysis okay that's Really what these steps are uh um and then let's look at the result again I'm going this super fast we really not talking about how to do it per se exactly right but we're just introducing the basic step so you can sort of this is a defamation plot of the fan against the ball this is the stress plot now I don't have much information about Contour but you can
sort of see you can sort of that makes sense right this is essentially like a beam the highest Stress point right there showing is around the connection point between the fan blade and and the and the center piece right and this is the defamation plot right so with something like this with enough investigation into the input parameter into my material into my inflation pressure for my ball into the mass of my ball I can start building a meaningful model to investigate is my fan strong enough enough to handle this kind of Perturbations right what's the
connection here what happens if I make my fan blade longer is that going to create a stress problem around around my fan blade right and what happens if the fans are rotating even faster right and what happen if I changeing the angle of my my fan blade these are all the question we are starting to able to be able to answer very quickly right once you construct a baseline model that capture the basic input Behavior to Capture the basic Behavior and the input parameter of the components of the model such as you know what are
the fan made of what are the connection points you know what are the mass of the ball what is the inflation pressure of the ball these are the things once you capture it we can start asking a lot of different questions right okay that's the first example second one right so in this case I'm going to do a quick ballistic analysis right and remember I have a Steel plate a copper bullet literally I don't even have a core that's steel I I have a core that's made of of copper okay because all I had was
a copper material for a uh for a simplified JC simp Johnson cook materal Model so I didn't want to make up a steel steel material model on to use something I do have right then I want to see the bullet shatter because I know a copper bullet against a a hardened seal plate is going to shatter right and the way to do this Is actually not with an FAA method it's also do what's called a structural a structural uh um arpat Lan model right basically what this means is that the structural side the lran side
is the steel plate and that's essentially still done with the final element right but the bullet is actually behave more like a fluid at at such a high impact velocity right so what you want to do with a model like this is that you want to treat the bullet uh Projectile as a essentially like a fluid right uh and the way you do that is to do to create what's called an SLE domain right which is like this little box right here and this little box is going to have a a sale mesh assigned to
it and that essentially acts like your control volume which means as the bullet the forms right Its Behavior going be dictated within that control volume because you're looking at it in a yian frame of reference as opposed to just a Lan frame reference like like you typ typically do in an FAA analysis right uh and then once you do that you what we also want to do is to sort of Define the behavior the contact Behavior between the fluid part or the yian part against the lran part which is a steel plane right so this
coupling object right here creates a constraint L Gran solid method right I'm sorry key card and that's going to essentially make sure that my my projectile parts and my steel play Parts the center piece right there is going to see each other as a contact paer right which means as the as the bullet shatters right he going to see the the the steel plate and not be able to penetrate it okay and then once you do that uh very very simple you can sort of see this is the the simulation side right you can sort
of see it shatters and you can sort of see this right here that's the limit of your control volume is where I I could have made the control Volume bigger in which you don't see this I probably should have done that but for the sake of demonstration I can sort of show you what happen and this is what happens with a YouTube video of of a bullet shatters you know not exactly the same remember they have a steel core inside here this bullet uh uh shape obviously is also different right but the idea within a
modeling approach is you know you want to do projectile analysis really like you know getting The material model right and getting the behavior right uh might be the CH might be more more expensive in terms of Investments right but the modeling approach is exceedingly easy to understand right as a simil you want to capture the way you want to do it uh it's really not that hard to do but once but the the key thing that you got to make sure you capture the the the internal material Behavior correctly right in this case I use
more of a dummy Copper material which is why the behavior is a little bit different and that's that's the basics of a of a ballistic analysis right all right next one let's look at a couple more right in this case I have a lower speed penetration problem but in this case right I don't want the projectile to shatter I want the play to be penetrated right so in which case case if the bullet is going to penetrate the plate what happens right and in this case I Have to switch around the the the the method
of simulation a little bit to treat the the play portion of of the geometry a little bit different and then what I'm going to do is what's called SPG a smooth particle gurin method right so instead of treating the this little gray part as as final element I'm going to treat it as smooth particle like an element free way of looking at it right um and then the way to really do that is that the material model um the section Cards which are defining essentially the the the nature of the formulations right of the behaviors
and then the equation of State these three things are going to be assigned to the centerpiece which tells that centerpiece how it's going to deform in the presence of external load right and it's going to be perform a lot more in in know element free method and I'll show you what happens if we don't do that in a bit as well right so basically these three cards which are Assigned to the to this object to Define this behavior is going to tell me tell us how that how the program how this thing is going to
form right I'm going to create a a uh a no set here I'm and using that no set of a one 100 right this ID right here I'm going to tell the penetrator which is a yellow piece and this little this bunch of nodes right here that they're going to see each other as contact pair right that's the logic right so the the nodes on in the Highlight area is going to see the penetrator in this contact card right here so you can sort of see the way I'm I'm setting up the problem really is
that you know um I'm I'm defining the characteris IC of my of my plate then I'm defining the contact between the penetrate and the plate just like you you would do with anything else but in this case I'm focusing my energy on the correct cards I want to use to define the correct Behavior right so this card Right here this contact card is going to set these nodes against these uh these surfaces on this yellow part and they are going to see each other as a contact pair right because remember this is not a simple
uh uh mesh against Mash contact anymore right this is more about particles contacting surfaces right and I have I have to Define it in a specific way using using this method right here right and then this is actually model with SPG instead of withing elements so What happens right so if you look at here this is the element free method right you can sort of see as the penetrator goes through against the plate you can sort of see this is a much more clear way of of where the the the the deformation where the fracture
happens within the plate right you can sort of expect this to happen but but if you don't do it this way if you just do it with the basic method of of of FAA method right you can see this element Just erodes right where the element basically just magically goes away right so the why is this not a good way of doing this right is because you are essentially losing the the conservation momentum right you can't have mass just disappear from the from the model you want to be able to capture its effect after fracture
occurs right so with the correct material model uh this method allows you to really capture the the reaction forces of your penetrator as it Hits the the play and can really capture that the damage Behavior much more closely right so this way this is a great way of doing penetrations right any kind of penetration problems that require a good capture of damage uh you can use this SPG method right of course you know get a better material model get it a better Behavior check your input parameter to get a really good model but the basic
modeling approach is essentially as I've demonstrated okay a Couple more all right um okay so this is a drop of a large electronic Appliance I'm going to go through the real quick this is a 2.7 Rion per second angle drop right against the floor basically um also something like this that you have to do right is build a contact all these joints and contact by the way I borrow this model from from ansers because I can't show you guys the our customer model and for something this large I couldn't create it myself right so but
Basically all you have to do for something like this and you build a contact to construct the entire assembly for the structure right to make sure everything's connected correctly any kind of boled connection you want to apply a bol preload and then U and then you want to apply a riger wall on the bottom so you can sort of think yeah the model like something like this could be could be pretty difficult to build right but really you are just Building contacts together and you're you're you're doing your preloads and then you're you're making sure
your your floor is correctly set up then you set your initial conditions then you can you can basically drop drop a larger plance like this inside dyam pretty easily right so you can sort of see something like this you can see the stress as it as it go through the drop you can actually just something like energy is something you always want to check right In an expess analysis so that in this case they check the energy for the for the problem right so replace this with any large appliances that you might be working on
you know we can certainly help you do a drop study pretty quickly right because something like this right when you have a a three four five ton structure under some kind of drop conditions right there always a a risk that you want to mitigate and an explicit package like Dina can do this Extremely quickly right where it's it's so proficient at doing something like this that it's so much faster than a lot of the of the package as well right and then with the workbench Al Dina setting up a large large model with thousands of
pairs of contact becomes really really easy to do okay all right uh a couple more two more I promise almost done two more right I want to show you so many things I wanted to show show in this webinar Like I'm almost giving myself too much to to to present but two more two more to go through right this is a burre model so I have a very simple turbine uh uh structure right I I basically created with nothing but these shell bodies right then this this is the bir stke shape now bird stke shape
if you're not familiar with these are like a wellestablished modeling methods right so for different applications the Aerospace working group presented Different bir strike shape that one can use you essentially model these with like water right and then you're G to hit them against your against your structure depends on what kind of structure it is in this case it's a turbine so I just model something very similar to this and I use it for for the demonstration purposes right now for something like this you're going to have to use something called SP right which is
a essentially it's also another way Of doing doing particles right so you're not really modeling the bird shape with elements you're modeling with particles like this right uh and this particle uh if you if you imag if you remember everything we just talked about right it's going to have a contact defined between the particle and the blade which is what we're doing here we're going to define a set for the nodes we're going to define a set for the bodies and then we're going to define a contact between The noes and the bodies which is
which is really the essence of what it is right so this contact card is going to look for set ID 102 and set 101 102 is my noes 101 is my body right and that's going to tell the program that the no these these little water particles right is going to hit against the blade bodies and then we're going to see what happens with them now before I do that I'm also going to define the contact between the individual components of my blade and my Of my turbine to in case they break I want to
be able to see the their their contact to each other right so that's really what this body interaction object is it creates what's called a single surface group uh Group contact so this 101 set ID is going to basically include everything that's highlighted in in blue right here and that's going to create a a self self contact condition basically any portion of the anything that's highlight in PL can see each other as a Contact pair uh that's really what these body interaction would translate to a single surface contact is it's it's essentially a blade set
okay and then lastly I'm going to define the failure condition of my turbine blade which means that you know at what stream uh plastic stream value or effective stream value is my blade going to essentially get close to the area where it's going to fracture and break apart right so a a way to simplify uh this kind of Defamation of damage is to use what's called a matad add erosion this is essentially a c and Dina that allows you to define a 15% effective plastic string and 5% principal uh string right tens princial string is
going to cause the dur blade to break which means any area where you you see enough strin right the element itself will erode and you're going to see something like this right the the water particle will break apart on it hits a turbine blade and in the Area where it directly hits you're going to see fracture that happens right so in quick summary something like this looks pretty cool right but really all we did is we created a shape we're going to call that shape a particle shape we're going to define the contact between the
particle shape and my turbine blade we're going to define the contact between the body of my turbine blade then we're going to define the fer criteria for the turbine blade then bam I have a pretty much a model ready to go now of course I have some initial condition here that I didn't talk about um but that's really the nature of the of a birth strike analysis right and because the birth strike shape and the materal model of the birth strike shape is a well-published information that we can use for a much more complicated turbine
shape right this turbine shape is made up but we can do we can do this kind of analysis for anything that's Much more complicated in real life right because the process isn't really changing what is changing is the nature of the input parameter like we need to understand the structure it's stiffness the material we're using the way it's it's built together but the process of building it of building a model the modeling approach is the same as a simple model that I'm showing you here okay and the very last thing I will show you guys
right hopefully you're not You're not uh you're not too bored right is that if you ever seen those drone capture device out there where people are building these nets to capture drones right uh obviously I can't do something that complicated on the flight in a c in a c program myself so what I did was I built a a tennis uh net I'm sorry a volleyball net I look up some basic dimension of a volleyball net I I look up the basic preload they use right and then I'm going to create a Situation which I'm
G to ask the question you know at what point does the volleyball go over the Net versus being stopped by the net right so if you can imagine a volleyball hitting the net why did it sometime go over why it sometime being stopped right that's the question I'm going to try to ask uh Myself by running a simulation in Dy okay so pretty simple structure something like this right um um basically the ball is still a Rubber ball uh you know pretty simple because I want to use the same thing I've already used right so
same Rubber Ball assigned to the volleyball these beams right here are basically just uh just the Nets right these nets right here are basically I gave it some kind of plastic material uh because I I don't technically it's some kind of fabric right so you can sort of look exactly how those those volleyball net are made um I won't I won't dig too much into it So I just did some very quick and plastic material I use I have in my in my database the PO which are these right here I use I use the
420 steel because I want these to be really stiff right as they should be and these are solid big poles in real life now um these prelow right so these nets are not just sitting there if you know like there are usually pulley in the around the around the post in the left and right hand side which is going to add a lot of preload to stretch The net and and to pre-tension it right so I want to model that pre-tension Behavior by basically doing both preloads even though they are called both preloads all I'm
doing here is I'm creating a beam between this this point and that point right and then I'm GNA I'm going to tension it uh basically create a preload tension in by the in in the presence of a by utilizing a beam model Beam Beam object in between the the this this point right here and this Point right here and these four pre both preload is basically just me preloading one two three and four and I going to stretch the net in the beginning before the volleyball hits right and that's basically my again my Dynamic relaxation
I'm going to preload it which is allows my net to behave more like a volleyball net right and then lastly no I'm going to create my initial condition in which my ball is going to be inflated and it's going to hit against the net at a 1,000 Inch per second some number I made up right something pretty close okay so you can sort of see at the very beginning right so before I stop before I do go over too much you can sort of see this is the post here this is the post here you
can see the net this is the def the total defamation plot right the KN is being stretched on the left hand side being stretched on the right hand side it tells me it's pretensioned right and then as the as as The volleyball hits it it's going to stretch and then bounce the ball back now you might say I think this this KN is probably a little bit too elastic I will say because I use plastic As opposed the actual fabric material and maybe my my beam is a little a little bit different but remember I
drew this basically with like 10 minutes right I'm not trying to actually create a volleyball net but that's the approach right if I get an actual volleyball net I can I can do the same analysis with with with an actual geometry right with somebody who's actually design designing this right no that didn't that didn't go over now what happens if I make the volleyball two inch higher above than net right you can sort of see that the volleyball will actually go over uh and and that's that's an interesting Behavior to think about because this is
very similar to any kind of like net Capture device that we will do right is that you essentially have a cable pretension system that you want to be able to capture the stiffness and the contact if you're correctly and that's the entire nature of any kind of net capture device model right which is the same thing as a volleyball model a volleyball net model because we're trying to do the pretension correctly and we're trying to capture the net stiffness correctly then we're trying to Capture the contact between the projectile whether not be a drone or
a ball against the net once you capture those elements of the model correctly we can correctly capture uh the entire physical Behavior okay um a lot of information for you guys right but basically basically you know din is the go-to thing for explicit but it has such a wide range of capability in inide say for example implicit doing moto analysis Doing response Spectrum doing vibrations doing thermal right you really want to look at it investment in Dina as just as more than just doing things that that's like a crash like crashing a car right you
really want to look at it as a much bigger investment into the expanding the the simulation capability that really doesn't exist Within a lot of other other code that you might have access to including say for example an mechanical which is the default impl mechanical uh Package that we have um you know uh and know that the pre-processor and the postprocessor right people can use product that's not within Anis but consider the the workbench Alina as the one that we offer I think this is going to be the the future uh uh pre-processor everybody wants
to use because it's developed by the by the people who own D now okay that will be the end of my presentations thank you all right uh thanks sis and uh just as a reminder to Everybody um everything's being recorded and we're going to send it out to you here in the next couple of days and if you have any questions we do have a few questions here um feel free to type them in at this time and we're going to give you a few moments to do so and just as a kind of a
final closing statement um as uh Elite Channel partner uh we can help get you set up with Lis DIN and make sure you have the right tools to do your simulations as well as uh we have a full Consulting team in house including Dennis uh so even if you don't have uh Dina or you're looking for other options or you want some help uh from one of our team members we would be more than happy to help you there um but other than that Dennis I will uh I will start asking you the questions you
good sure yeah go ahead perfect um all right the first one I have is from David uh can Anis LS din take advantage of system symmetries yes it can so you can Actually insert symmetry object it actually gets transferred to what's called SBC card in Dina but you basically behave like you would expect a symmetry condition to behave perfect uh and just so everyone knows we we'll stick around for a few more minutes I know it's getting close to the hour here but we have a quite a few questions that came in so um next
one I have here Um let's see it's from Ben I'm using Ellis din now most of my experien is within implicit FEA like Anis and Abacus explicit simulation show stress waves propagating quickly through the solid how do you ensure you get mesh convergence in the explicit solid sorry let me explicit solve uh convergence doesn't apply to explicit uh methods right so hopefully you understand that so when we talk about convergence is purely a a artifact Of the implicit method where you have to check for convergence within each step within each substep of your analysis explicit
is is is essentially propagating through the the the the step of your analysis very quickly with a very small time step with a condition such that you need to get within a small enough of a Time step to remain stable and this is one of those questions that's more around the the foundational understanding of the difference between Implicit and explicit now Dina if you can also do it as an implicit analysis which will also require you to to check for convergence but key things to remember that if doing an explicit analysis it's not about convergence
you don't have to check for that uh that's the that's why you do explicit really is that because you don't have to check for convergence there's a lot of benefit because of that the downside is you know you have to pay attention to the the Size of your element the the the size of your time step and also how long what's the duration of your entire run and explicit analysis are limited by those factors perfect okay we have a few more here so um this one's from Hong uh how did check key cards in the
guy can we modify the inputs in key cards yeah so good question so you cannot modify the key cards directly within a pre-processor right remember the the idea of a pre-processor whether Or not use hyper Mash or feap or workbench Alina right is that you essentially creating objects like guey right things that you can insert click on all that stuff the key cards are what's generated into a text file now you can edit the text file after you write the input deex from your pre-processor right you can certainly do that uh but the pre-processor is
always about creating objects in a in a graphic user interface in which in which you Will have equivalent input de that's being written at the end right so remember editing input de you do that within a text file environment not within the the the the gooy itself right that's that's contradictory in sense perfect let's see here we have a couple more uh this one's from Brian uh can you generate one mesh that you use in both Anis implicit and Dina explicit analysis yes you can uh it's not entirely Recommended this is a little trickier question
so the basic idea here is that any mesh you generate right can be used for whatever solware you want to send it to right so in implicit mechanical uses the apdl solver as you I'm sure you understand right Al workm Al uses the Alo solver right so you can send the same mesh body to those two solvers but what you want to pay attention to is things like element formulations right the element order these are the things That are different between they have different requirements between instance implicit and Alis right because Al is going to
require you to have a different you can you actually you actually can Define like section thing section informations inside work inside ala that that doesn't make any sense for for apdl solver right so pay attention to the element formulation element order right section informations these are the things that that's need to change Between given which whichever s you're sending into but the mesh body right is interchangeable right you can use it for whatever reason you want to use it that makes sense hopefully yeah perfect uh Dennis there's a ton more that are coming in so
do you have a few more minutes I have time I have time go ahead perfect we'll hang around for like another five 10 minutes and then just so everybody knows we will uh I'm going to take all these questions and and if we Don't get to it we will have someone reach out to you and make sure that we follow up with you so sure sure um let's see here this one is from Fang uh hi Dennis could you please tell me what's the termination of your fan ball impact model fan ball imp which one
is that the one with uh this one right here yeah the first one with the rubber ball and the fan I think the termination you mean Like the termination time is that what you mean uh it just says could you please tell me what's the termination of your fan ball impact model uh I'm not sure exactly I understand what that means I think this thing runs for like 02 seconds if that's what you're trying to to to to ask basically I let the fan rotate for I think 02 or 0.5 seconds I think that's what
I did I don't remember honestly the control termination might be what he's trying to look for usually That that tells you how long that the model ran okay maybe answers your question ask a follow-up question if that that doesn't answer your question okay I can try perfect uh let's see here another one from Daniel um building off the previous question what exactly is the difference between explicit and implicit solvers uh well implicit problems require you usually are ones that runs Longer require you to to you can really run with as large of a time set
as you want explicit analysis are are limited by for example the size of your element the the essentially the the speed in which sound travels through your material right so that limits the time step that you have but the benefit of an explicit analysis is that you don't have to check for convergence uh that's usually a good way to to look at it right it's essentially different way to Propagate through the state of a system right so if you have a model that that takes a long time to run for example the physical event takes
a long time to proceed you usually have to approach that problem with an implicit method because the duration of the physical event is very long if you have an impact event right the duration of the impact event is usually in in in order of microseconds and those type of problems are usually also one which includes Large uh deformations right in these cases right it's much more suited for for an explicit analysis because in explicit analysis you don't have to check for convergence and you can you can propagate through analysis much faster so really the difference
between the two it it's about the nature of the problem like how how linear nonlinear it is and what's the duration of the physical event and that usually dictates uh whether or not you want to you want To approach a problem implicitly or explicitly right hopefully that answers your question the the answer to that can get much deeper right I don't know if you're looking for even deeper answer to that these are the these becomes more and more of a text full question once you get deeper and deeper than that hopefully that answers your question
yeah we have we have a ton more here so we'll go that's fine okay we uh we'll go for another five or so minutes here for Everybody um we have one from Kell uh thank you for the informative presentation I was wondering if it is possible to establish a connection between Ellis dinina and Anis apdl in a manner similar to the integration provided by Anis workbench wait Sor say it again establish a connection between what Lis Dina and Anis APD l in a manner okay you a matter what you a matter what say again oh
sorry in a manner similar to how the integration uh is provided With workbench uh okay so so so I I guess this confusion here is this right so the an is workbench Alina uh environment which is the the which is this thing I'm showing on the screen if you can see me you see this thing I'm showing you on the screen right that's the pre-processor uh used to write an input deck which is a k file that look like this I don't know if you can see on my screen right here right and that's a
a Input deck that's be us that's be that's only going to be used for for uh work for aloso solver the apdl solver requires a different format of input right it's it's actually a DAT file contain a bunch of a apdl codes if you ever look at like if you ever run an instance mechanical model right and you look at exactly what is writing out is writing out a that file. datat file and that's actually completely different so workm Dina does not have anything to do With apdl Sol right there are completely different things hopefully
that that answers your question yeah all right let's see we have one from Matlock uh says excellent presentation how do you ensure sufficient gap between objects when you are defining uh initial velocity on an object before impact so the time is not wasted oh good question uh I mean this is is really about about geometry Preparations right so so uh you want to make sure you you maybe leave a little bit of a gap that may not be a bad idea because sometimes you might have initial penetrations due to the nature of the model set
up right uh but all that's really all you have to do is to make sure you have a very small amount of Gap such that the only the first few Cycles within your explicit analysis is going to have no contact and the rest of it is going to just impact um so to answer Your question I guess in simple terms let's just make sure you excuse me do your jum prep correctly I think that that's going to going to mostly do it hopefully that answers your question uh you know just uh uh geometry preper really
is where you want to do it yeah so this one we might have to follow up on uh for David uh are there any examples of aeroacoustic problems available and I'm assuming like within the sample models Yeah I do not know much about AER Acoustics but please follow up with that we'll find people who know have the answer for you myself is I do not know much about it so unfortunately I'm probably not much help in that regard perfect uh let's see here um uh why okay this one's really good I think why why would
I use Anis LS Dino over mechanical uh so remember right you know when you are a when you when you when You or your organization have simulation capabilities right aners mechanical is mostly or I should say entirely implicit code right so aners mechanical so if you buy the an mechanical say for example Enterprise or premium license right you do get an explicit Dynamics package but alos dinina is a far better and honestly a far more developed explicit code right so why do you need an explicit code is that because there are problems you simply cannot
do inside implicit so one Of the gentlemen earlier asked you know what is the difference between implicit and explicit right so imagine you have a problem that uh you know that's very very short in duration like impact but also have extremely large deformation so you really cannot do that kind of problem in s mechanical right and that's where you need an explic it doesn't have to be dyam but you're going to need it now some some company may not need to do these highly transient situations then You might make an argument that you do not
need Dina but remember the the key point I want you guys to take away from the presentation right is that alas Dina is also a highly capable implicit code right so so you can use Dino to do all of it but you can only use something like aners mechanical to do implicit right so that's why you want to look at Dina as a potential package because not only can It allow you to do things you can currently do it can also allow you To do things that you can do but do it even better in
some situations so hopefully that answers the question y great and then uh looks like we have a couple just saying excellent presentation thanks Dennis uh from a couple people here and then just one final one here um we have a question from uh someone that came in that's uh I have a consumer product my team is working on but we don't have Anis or any other simulation SE software how can Rand in your team help uh reach out to us I feel like you know if we could you know set up a call to understand
what you guys are working on like what is the challenge you're trying to overcome right I feel like we can certainly help you look at you know in two ways one is we can look at the specific program to see if our team can can help you using simulation tool that we do have to solve that problem for you right I think simulation is always about You know studying the physics behind whatever it is you are working on right so we are we really offer the service to understand the physics by using these tools for
with you and for you to see if we can find uh answers that that you may you may or may not have seen that's the first way uh I think the second way is you know we might be able to introduce the the simulation to into your organization through this initial collaboration right sort of to to give You guys a like a a window into you know if you have a problem like this how can simulation help you right we want to we want to sort of answer that question for you through this collaboration right
so I think the first step please reach out to us I I think there are people on the on the team you know uh more more more suited on the on the on the sale and marketing side than myself um to to answer that question even better but you know hopefully that answers your Question Perfect all right uh so just for everyone uh thanks for joining us today uh we did get a couple more questions but um we're going to just wrap things up and we'll reach out to everyone here in a followup uh that
did ask a question today um and thank you Dennis and everyone for joining us and I hope you have a great rest of your day thank you yeah thank you